Lab7 configurting network

However, some may wish to use Hyper-V on a laptop or a desktop computer. Perhaps to learn about Hyper-V, or create training material such as demos, for development purposes, or just for fun. Sometimes, because of company IT policies and management practice for servers, running Hyper-V on a laptop is the only way you can develop or document something.

Lab7 configurting network

Taylor Gibb April 18, Instead, you can just VirtualBox like we do to create virtual machines for all of your testing. A copy of VirtualBox which can be obtained here.

Setting Up Your Lab The first thing we need to do is get VirtualBox installed, and since this is a next, next finish type of install we are confident you will be able to get it done in no time. Once the installation is complete we are ready to create our first virtual machine.

Since we are going to have both clients and servers, we will call this one Windows 7 Client and select the Windows 7 operating system from the dropdown list, then click next.

A safe bet is probably 1GB though. Fixed size disks give slightly better performance from a HDD point of view and quite frankly we need all the performance we can get. So flip the radio over to the Fixed size option, then click next.

Once VirtualBox has finished creating our drive we are good to go. We still need to configure some settings though, so before you get too excited click on the Machine menu and select the Settings….

Lab - Building a Simple Network Topology Addressing Table Device Interface IP Address Subnet Mask Default Gateway S1 VLAN 1 N/A N/A N/A S2 VLAN 1 N/A N/A N/A • Cable a physical lab topology. Part 2: Configure PC Hosts • Enter static IP address information on the LAN interface of the hosts. 5 Study of basic network command and Network configuration commands. 6 Configure a Network topology using packet tracer software. 7 Configure a Network topology using packet tracer software. 8 Configure a Network using Distance Vector Routing protocol. 9 Configure Network using Link State Vector Routing protocol. Lab Configuring and Verifying PAP and CHAP Authentication Step 1: Connect the equipment Connect Router 1 and Router 2 with a serial cable connecting both Serial 0/0/0 interfaces as shown in the topology diagram.

When the settings dialog opens, switch over to the storage section, then click on the empty IDE controller which can be found on the right-hand side. Finally we want to head over to the network section and change the network settings from NAT to Internal Network.

This is very important.

Lab7 configurting network

Once you are done with all that you can go ahead and start the machine. Once it has booted it will be just like any other Windows 7 installation.

Now that we have a working virtual machine, you will want to go ahead and set up one or two more clients running Windows 7 and perhaps a single virtual machine running Windows Server R2 for our upcoming Geek School articles covering Windows Server. Right click on your network adapter and open the properties.

Now change the radio button option to allow a static IP address assignment, then set your IP to For each virtual machine you bring on the network you will need to increment the last digit in the IP address by 1.

That means your first virtual machine will be The subnet mask must stay the same for all virtual machines. You should now be able to ping any virtual machine from any other virtual machine.In a later lab (lab7), you will learn how to encrypt mail messages send via After configurting and restarting your MTA, you now need to install, on your virtual network.

Smith (student) settings w SMTP Get a nt ere fMd by the ssuns STAR Setup Thunderbird MUA. Part 1: Build the Network and Configure Basic Device Settings In Part 1, you will set up the network topology and configure basic settings on the PC hosts, switches, and router. Step 1: Cable the network as shown in the topology.

Step 2: Configure PC hosts. Step . Network Windows 7 Configuration MOAC Lesson 5 – Connecting to a Network Unit 3. Lab 3. Configuring Network Connections Do exercises Unit 3.

Microsoft Specialist: Windows 7 Boot Camp for Desktop Support Technicians - Global Knowledge

Problem Set 1. Unit 3 Problems Unit 3. Assignment 1. IPv6 Addressing Assignment 3 assigned Unit 4: Working with Workgroups and Domains Windows 7 Configuration. Hyper-V: How to Run Hyper-V on a Laptop.

This article is a work-in-progress. Please feel free to correct and extend it. It is the Wiki way! On the Hyper-V Virtual Network manager, create a virtual network adapter named Virtual External Wireless Network and configure it as an Internal only network.

RIPng is based on RIPv2 and has the same administrative distance and hop limitation. In this lab, you will configure the network topology with RIPv2 routing, disable automatic summarization, propagate a default route, and use CLI commands to display and verify RIP routing information.

Network Teaming, or Team, is designed to implement the concept in a different way by providing a small kernel driver to implement the fast handling of packet flows, and various user-space applications to do everything else in user space.

Routing and Switching Essentials Lab Manual